 | Myford series 7 manual Ref: 939
Author Ian BradleyPages 232This book is a must for all myford owners.this book covers: 1- The Myford ML7 Lathe 2- The Myford Super 7 & ML7-R Lathes 3- Installation 4- Lathe Tools 5- Sharpening Lathe Tools 6- Mounting Work in the Lathe7 - General Turning , drilling and boring in the lathe8-Threading & Screwcutting in the Lathe9 - Milling in the Lathe 10- Gear Cutting in the Lathe11-Taper Turning 12 - Repetition Work 13- Additional Fitments & Operations 14 - Maintenance 15 - A Two tool back toolpost 16 - Attachments for the back toolpost 17 - Design Changes 18 - Formulae for Gearing 19 - Tables for Threads 20 - Lubrication Charts.a very good book for begineers £10.95
|
|
 |
 | Model engineering book (a foundation course) Ref: 24
Author Peter WrightPages 408This book covers:the introduction and principles and supplies, setup of a workshop, measuring and marking out, basic hand work, bending / folding and forming, metal joining, hole production, screw threads, essential machine tools, principles of turning, holding work in the lathe, adapting the lathe, buying a lathe, basic lathe practise etc, 17 chapters full of informative advice. £17.50
|
|
|
 | The amateur's lathe Ref: 937
author l h spareyPages 221this book covers: the lathe, choosing a lathe, installing a lathe, measuring equipment, lathe tools, drills and reamers, marking out, holding work in the lathe, lapping, metal spinning, taper turning, screwcutting etc etca very good book for begineers £9.50
|
|
|
 | The amateur's Workshop Ref: 938
author Ian BradleyPages 256this book covers: the lathe, choosing a lathe, suds equipment, reamers, the dial indicator, toolmakers buttons, belt drives, the back toolpost, measuring equipment, lathe tools, drills and reamers, marking out, holding work in the lathe, lapping, taper turning, screwcutting etc etca very good book for begineers £9.50
|
|
|
 | Dividing book Ref: 43722
author harold hallPages 104this book talks you threw the mathematics, pitch circle diameters, simple dividing divices,the methods, gear cutting, rotary tables and dividing heads etc etc £7.30
|
|
|
 | Tool and cutter sharpening book Ref: 935
author harold hallPages 133this book covers sharpening drills/endmills/milling cutters, small workshop tools, making a grinding and other tool rest's £8.30
|
|
|
 | Milling operations in the lathe book Ref: 6537
author Tubal CainPages 125this book talks you threw all kinds of milling operations on a lathe including: milling cutters, workholding, milling attachments, indexing and dividing etc etc £7.30
|
|
|
 | Sheet metal work book Ref: 563
author r e wakefieldPages 151this book talks you threw all kinds tools, metals and there characteristics, marking and cutting, seams and edges, rivets and riveting, welding and lots lots more £7.30
OUT OF STOCK |
|
|
 | soldering and brazing book Ref: 576
author tubal cainPages 136this book talks you threw all kinds of solders, brazing techniques, fluxes, brazing equipment, brazing alloys, fuels and gases, safety precautions etc etc £7.30
|
|
|
 | making clocks book Ref: 934
author stan brayPages 124this book talks you threw all kinds of pendulums, escapements, the going train and motion work, wheels and pinions etc etc £7.30
|
|
|
 | The compact lathe (revised edition) Ref: 936
author stan brayPages 187this book covers: safety, care of a lathe, lathe tools, turning operations, centre height, using a 3/4 jaw chuck, the face plate, turning radii, drilling and boring, screwcutting, milling, graduating and dividing etc etc £8.30
|
|
|
 | Workholding in the lathe Ref: 940
Author Tubal CainPages 111This book covers:Between centre work, face plate work, general chuck work, universal or independant chuck, the self centering chuck, unusual chucks, collets, work steadies and lathe alignment.a very good book for begineers £7.30
|
|
|
 | Milling a complete course Ref: 941
Author Harold HallPages 144This book covers:getting started, tee nuts, an angle plate, clamps, parallels, boring heads, dividing heads, grinding rest, the end mill sharpening fixture, tool and cutter grinding head.a very good book for begineers £7.30
OUT OF STOCK |
|
|
 | Workshop drawing Book Ref: 966
Author Tubal CainPages 114This book covers:the rules and "grammar" of drawing, dimensions, tolerances, machining marks, reading drawings etc etc £7.30
|
|
|
 | Unimat 3 lathe accessories book Ref: 968
Author bob loaderPages 185This book covers:the milling table, tap wrenches, 90mm faceplate, adjustable toolpost, tungsten carbide tooling, attachments for dial gauges, punches, a simple indexing set up and alot more over 14 chapters. £7.30
|
|
|
 | foundrywork for the amature Ref: 969
Author b terry aspinPages 103This book covers:foundry sand, crucibles, the furnace, moulding boxes, the melting procedure, cores and core making and alot more over 10 chapters. £7.30
|
|
|
 | elecrtro plating book Ref: 970
Author j poynerPages 61This book covers:the introduction and principles, the electric supply, the plating tank, the cleaning of the substrate,the finishing of aluminium and its alloys, over 9 chapters £7.30
|
|
|
 | model engineers handbook (third edtiion) Ref: 30
Author Tubal CainPages 240This book covers over 13 chapters which include:units and metrication, workshop calculations, standard tapers and collets, screw threads,workshop practise, metal joining, properties of materials, steam and the steam engine, air and gases, boiler work, piston and gland seals, electrical memoranda, and a general section, this book is like a model engineers bible £10.50
|
|
|
 | Making small workshop tools Ref: 40
Author Stan BrayPages 95This book covers :marking out tools, benchwork, lathe work, odd leg calipers, beval, scribing block, fly cutters, pin chucks and lots lots more £7.30
|
|
|
 | Electric motors in the home workshop Ref: 52
Author Jim CoxPages 133This book covers :safety, single phase induction motors, three phase, commutatotor motors, overhaul and reconditioning, mobile power, battery power, component suppliers, motor power rating. 14 chapters. £7.30
|
|
|
 | photo etching Ref: 100
Author Brian King and Azien WatkinPages 111This book covers :uses advantages and limitations of photo etching, preparation of artwork using the drawing board and cad,component design, the maths bit, and sheet layout. £7.30
|
|
|
 | Basic Bench work Ref: 105
Author les oldridgePages 127This book covers in 19 chapters:materials, reading engineering drawings, hacksaws, files and filing, hammers, chisels and punches, scraping, measuring, marking out, drills and reamers, taps and dies, soft soldering, all soldering and brazing,hardening and tempering lots and lots more £7.30
|
|
|
 | Drills Taps and Dies Book Ref: 112
Author Tubal CainPages 103This book covers in 13 sections:twist drills, drills of other kinds, drill sharpening, drill chucks, screw threads, taps and dies general, hand taps, tapping drills, screwing dies, tap and die sharpening, tables etc £7.30
|
|
|
 | Workshop Materials Ref: 113
Author Alex WeissPages 147This book covers in 14 sections:iron and steel, aluminium and copper, other non ferrous metals, selected materials, plastics, wood, refractory and abrasive materials, cleaning and etching, plating etc etc etc £7.30
|
|
|
 | Home Workshop Hints and Tips Ref: 114
Author vic smeedPages 115This book covers :lathe and lathe work, cutting metric threads, knurling troubles, machine tools and accessories, electrical, a simple forge, a simple furnace, low temperature solders, there is lots and lots in this extensive book. £7.30
|
|
|
 | The Backyard Foundry Ref: 115
Author b terry aspinPages 90This book covers :basic principles, patterns, plate patterns, cores, core boxes and core making, casting locomotive cylinders, wheels, metals, a solid fuel furnace. £7.30
|
|
|
 | The Art of Welding book Ref: 122
Author w a vausePages 95This book covers :arc welding, excercises with mild steel, brazing, oxy-flame cutting, pipe welding, weld symbols, welding defects, vertical and overhead welding of mild steel. etc £7.30
|
|
|
 | Model Engineers Workshop Projects Ref: 131
Author harold hallPages 103This book covers :tapping guides, guided die holder, large tap wrench, distance gauges, lathe tool height gauge, tailstock die holders, faceplate and angleplate clamps, lathe collets, thin piece collets, low profile clamps, tapping stand, etc etc £7.30
|
|
|
|
|
 | Lathework A Complete Course Ref: 151
Author harold hallPages 165This book covers :getting started, a mini surface gauge, precision square, a between centers test bar, hole gauges, distance gauges, tailstock dieholders, precision tapers, screw jack, getting to grips with the face plate, mill drill spindle, a milling chuck cutter. £7.30
|
|
|
